Bracelet Sizing
How do you remove links from a watch band at home?
Most metal watch bands are held together by pins. Put the band in a link removal tool, find the small arrows stamped on the inside of the links, and push each pin out in the direction the arrow points. Take the same number of links off each side of the clasp, rejoin the band, and push the pin back in against the arrow. A kit with a pin pusher costs well under $20. If the links have tiny screw heads on the side instead of pins, use a precision screwdriver, never a pin pusher.
Pins, screws, or pin-and-collar: check first
Look at the side of the band. Most affordable bracelets use push pins: a plain round end on each side, and small arrows on the inside of the removable links showing which way the pin comes out. Some pins are split (folded) pins that grip by spring tension; they come out the same way.
If you see a slot like a tiny screw head on the side of each link, the band uses screws, which is common on higher-end watches. Unscrew them with a properly fitting flat precision screwdriver; a pin pusher will damage a screwed link.
Some bracelets, including many Seiko bands, use a pin with a tiny metal collar inside the middle link. The collar is easy to lose when the pin comes out, so work over a tray or a light-coloured cloth.
How to do it, step by step
Measure first: put the watch on and pinch the excess band together to count how many links need to go. Aim for a fit where you can slide one finger under the band.
Lay the band in the tool's holder with the arrow pointing down toward the hole in the base. Line the tool's pin over the pin end and turn the handle (or tap gently with the small hammer) until the pin slides out the other side. Remove the link, then do the same on the other side of the clasp, so the clasp stays centred under your wrist.
To rejoin the band, line up the holes and push the pin back in from the opposite side, against the arrow, until it sits flush. Tap it home gently with the hammer if needed.
For a finer fit than a whole link, most clasps have two or three small holes for the spring bar near the buckle (micro-adjustment). A spring bar tool lets you move the clasp one hole without removing a link.
Which link removal tool to buy
You need three things: a holder that grips the band, a pin pusher (either a screw-handle press or a pin punch), and a small hammer to tap pins back in. Most kits add spring bars, spare pusher tips and a spring bar tool, which is useful for changing straps.
The kits below are the best-reviewed versions of that set on Amazon. They are all inexpensive, and any of them will size a typical steel bracelet. A jeweller will usually do it for you too, often for a small fee, which is the safer choice for an expensive or screwed bracelet.
Keep the spare links
Put the removed links and pins in a small bag and keep them with the watch box. Wrists change size with heat and over the years, and a watch sells for more with all of its original links.
The tools we would buy
Best overallJOREST watch link removal kitLink remover, pin punch, double-headed hammer, band holder, 20 spring bars and 13 spare pusher needles.See it on Amazon →
Most complete kitEFIXTK 60-in-1 watch band tool kitPin remover with 6 extra tips, band holder, hammer, a spring bar tool, 20 spring bars and 20 cotter pins.See it on Amazon →
Easiest to line upJOREST link removal kit with lifting platformThe holder and remover are one tool with a liftable platform, which makes it easier to line the pusher up with the pin hole.See it on Amazon →
Also for leather strapsJOREST link removal kit with leather punchThe usual remover, holder and hammer, plus a leather strap punch for adding holes to leather bands.See it on Amazon →As an Amazon Associate, we earn from qualifying purchases.
Frequently Asked Questions
Which way do you push a watch pin out?
In the direction of the small arrow stamped on the inside of the link. Push the pin back in the opposite way when you reassemble the band.
Can I remove watch links without a tool?
People do it with a thumbtack or a small nail, but it is easy to scratch the band or bend the pin. A link removal kit costs very little and holds the band steady, so it is worth having.
How many links should I remove?
Put the watch on and pinch the extra band together; each pinched link counts. Remove them evenly from both sides of the clasp, and check that one finger slides under the band.
What if my watch links have screws?
Use a flat precision screwdriver that fits the slot exactly, and turn gently. Some screwed links have a screw on each side; do not force a pin pusher through them.